graphite electrode hp factory

Pubdate: 07-12 2021

Graphite electrode hp factory product classification

graphite electrode hp factory

(1) Ordinary power graphite electrode hp factory. Ordinary power graphite electrode hp factory is an ordinary power electric furnace that allows the use of graphite electrode with a current density lower than 2. The hp factory is mainly used for steel making, silicon making, and yellow phosphorus making. The national standards of ordinary power graphite electrode hp factory are as follows:

①For wet graphite electrode hp factory, it should be dried before use.

②Remove the foam protective cap on the spare graphite electrode hp factory hole, and check whether the internal thread of the electrode hole is complete.

③ Use compressed air that does not contain oil and water to clean the surface and internal threads of the spare graphite electrode hp factory. Avoid cleaning with steel wire balls, metal brushes, or emery cloth.

④Carefully screw the connector into the electrode hole at one end of the spare graphite electrode hp factory (it is not recommended to directly install the connector into the electrode removed from the furnace), and do not hit the thread.

⑤ Screw the electrode sling (graphite sling is recommended) into the electrode hole at the other end of the spare electrode.

⑥When lifting the electrode, put a soft object under one end of the spare electrode installation connector to prevent the ground from damaging the connector; extend the hook into the hoisting ring of the spreader and then lift it. The electrode should be lifted smoothly to prevent the electrode from falling off or from the B end. Collide with other fixtures.

⑦Hang the spare electrode above the electrode to be connected, align it with the electrode hole, and then slowly drop it; rotate the spare electrode to make the spiral hook and the electrode rotate and drop together; when the end faces of the two electrodes are 10-20mm apart, clean it with compressed air again The two end faces of the electrode and the exposed part of the connector; when the electrode is completely lowered at the end, it should not be too strong, otherwise the electrode hole and the thread of the connector will be damaged due to a violent collision.

⑧Tighten the spare electrode with a torque wrench until the end faces of the two electrodes are in close contact (the correct connection gap between the electrode and the connector is less than 0.05mm).

(2) Anti-oxidation coating graphite electrode hp factory. Anti-oxidation coating graphite electrode hp factory is a graphite electrode hp factory coated with an anti-oxidation protective layer (graphite electrode hp factory antioxidant). The formation of a protective layer that is both conductive and resistant to high temperature oxidation can reduce the electrode loss (19%-50%) during steelmaking, prolong the service life of the electrode (22%-60%), and reduce the electrical energy consumption of the electrode. The promotion and use of this technology can bring about such economic and social effects:

① The unit consumption of graphite electrode hp factory is less, and the production cost is reduced to a certain extent.

② The graphite electrode hp factory consumes less electricity, which saves electricity consumption per unit of steelmaking and production costs.

③Because the graphite electrode hp factory has less replacement times, it reduces the labor of the operator, reduces the risk factor of operation, and improves the production efficiency.

④ The graphite electrode hp factory is a low-consumption and low-pollution product. It has very important social significance today in advocating energy conservation, emission reduction and environmental protection. This kind of technology is still in the research and development stage in China, and some domestic manufacturers have already started production, but it has been widely used in developed countries such as Japan. At present, a company specializing in importing this kind of anti-oxidation protective coating has also appeared in China.

(3) High-power graphite electrode hp factory. High-power graphite electrode hp factory is a graphite electrode hp factory that allows the use of a current density of 18-, and is mainly used for high-power electric arc furnaces for steelmaking.

(4) Ultra-high power graphite electrode hp factory. Ultra-high-power graphite electrode hp factory is a graphite electrode hp factory that allows the use of higher current density, and is mainly used for ultra-high-power steelmaking electric arc furnaces. As a graphite electrode hp factory manufacturer, CGM New Materials Co., Ltd. will produce first-class graphite electrode hp factory products in strict accordance with industry standards and procedures.


Get the Quote

Send Mail Get Quote